How To Make A Waterfall Window Valance
Download Commodity
Download Article
A waterfall valance is a special window treatment that drapes down to resemble a waterfall and can give your windows a refined appearance. Hanging a waterfall valance correctly is trickier than hanging traditional curtains, but becomes like shooting fish in a barrel once y'all understand what you're doing. Earlier you hang your waterfall valance defunction, make sure to atomic number 26 them and choose colors that volition compliment the room. Then, information technology's just a affair of post-obit the right steps to hang them on the rod.
-
one
Mensurate the width of your window to determine your curtain rod length. Apply a tape measure and measure the peak edge of your window. Write down the measurement and purchase a rod that is 8–12 inches (20–xxx cm) longer than the width of your window. Mark the areas on the wall where you lot want to install the drapery brackets.[1]
-
2
Measure from the acme of your window to the floor. Utilise a record measure and measure the distance between the peak border of your window frame and the floor. This will help you determine the size of the curtain panels that you'll use to environment your waterfall valance.[2]
Advertizing
-
3
Install a double-curtain rod or 2 individual rods for a layered effect. If don't accept any rods installed, use a double curtain rod. Mark four–eight inches (ten–20 cm) on the left and correct side of the top edge of the window. This will be where you install your brackets.[3]
- You can purchase a double-curtain rod online or at a hardware store.
-
4
Install a valance rod if you already have a drapery rod installed. If you already accept a rod, you can use your existing rod for the curtain panels on the sides of your valance. Install the brackets for the second rod a couple of inches higher up your existing rod. Use the original rod for each of the valance'due south side panels and employ your new rod for your waterfall valance curtains.
-
5
Tape off the inside edges if using a detachable rod. A common rod style for waterfall valances is a detachable rod that comes apart in the heart. If you are using this rod, wrap masking tape effectually the sharp inside edges of the rod.[4]
- Taping off the edges prevents the curtains from getting defenseless on the rod and ripping as yous install them.
-
half-dozen
Iron your curtains if they are wrinkled. Ironing your curtains volition give them a crisp and neat appearance. Set the iron to low-medium oestrus so that you don't damage the valances.[5]
- If your waterfall valance curtains are already free of wrinkles, y'all tin can skip this step.
-
7
Decide which color valances you want to utilize. Yous can either use contrasting or matching colors, depending on your preference. Matching colors will give your waterfall valance a cohesive look, while contrasting colors will give it a layered, stylized expect. Hold the valances you programme on using side-by-side and decide if yous like the color combination.[vi]
-
8
Hang your curtain panels on the inside rod. Before you lot hang the waterfall valance, you can hang the 2 side pall panels that will hang to the flooring. Thread the summit of the panels through the inside rod and push them to the left and right side of the rod.
Advertising
-
1
Thread the left side of the first valance onto the rod. At that place should be an opening on both the left and correct side of each of your valances, and you'll use these to layer your curtains. Push the rod through the opening on the superlative of the first waterfall valance.[7]
-
2
Gather the material to the left side. Push the top of the valance down the mantle rod and bunch up the fabric on the left side of the rod. Doing this will give yous more room to add the additional valances to the rod.[8]
-
3
Add together the second valance to the rod. Have the left side of your second valance and thread information technology through the rod every bit you did the first one. The first and second valances should be bunched upwardly next to each other.[ix]
-
iv
Thread the right side of the showtime valance onto the rod. Have the opposite side of the first valance and pull it nether the second valance. Connect the right side of the showtime valance to the rod. The second valance should now exist overlapping and surrounded past the showtime valance.[x]
-
v
Add the third valance onto the rod. Take the left side of the tertiary valance and thread information technology to the left of the rod. The right side of your starting time valance should be touching the left side of your third valance.[11]
-
half-dozen
Thread the right side of the second valance onto the rod. Accept the right side of the 2d valance and thread it through the right side of the rod. This volition create the waterfall issue that you're trying to reach.[12]
-
7
Adhere the right side of the third valance onto the rod. Stop hanging your defunction by attaching the final valance's right side to the end of the curtain rod. If y'all did everything correctly, the valances should exist layered on top of one some other.[13]
-
viii
Connect the rods together if you're using a detachable rod. Connect the correct and left sides of the rod together and space out the valances so they don't look crowded. Your rod is now set to be hung dorsum onto the window.[14]
Advertisement
-
1
Hang the rod on the curtain rod brackets. One time you've fastened the valances to the curtain rod, identify it back on top of the curtain rod brackets. Look at the valances and decide whether the color matches the door frame and other elements nearby.[15]
- If yous don't similar the way it looks, unthread the curtains from the rod and utilize different color combinations until you attain the look yous desire.
-
2
Way the folds in the defunction. The folds in the curtains should be evenly spaced apart for a clean await. Fifty-fifty out the creases with your fingers and endeavour to make them expect compatible. This will heighten the style the curtains await.[16]
-
3
Pull the tops of the valances up. Pull on the top of the valances to remove any folds and creases and to give the top of your defunction a peachy look. Piece of work your style down the unabridged length of the valances until you've straightened all of the fabric on the top.[17]
Advertisement
Ask a Question
200 characters left
Include your email address to go a bulletin when this question is answered.
Submit
Advertisement
Thanks for submitting a tip for review!
Things You lot'll Need
- Masking tape
- Tape measure
- Curtain rod(due south)
Well-nigh This Commodity
Thanks to all authors for creating a page that has been read 18,810 times.
Did this article help you?
Source: https://www.wikihow.com/Hang-a-Waterfall-Valance
Posted by: trippcopievere.blogspot.com
0 Response to "How To Make A Waterfall Window Valance"
Post a Comment